Vehicles
Sections
186 not categorized PORSCHE 356A SHAFT O RINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1974-77 (includes uncategorized and accessory items) 021105279 Resides in the front relief of the flywheel mounting surface and always overlooked, this graphite seal it the final part needed to keep the oil in the engine case one required View/Change Diagram
From $1.95
Make a selection 99905204300 Known as: four-point bearing View/Change Diagram
From $161.00
Make a selection 99911014601 Cylindrical roller bearing located on the pinion shaft, nearest 4th gear. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. View/Change Diagram
From $261.64
Make a selection 99970108450 This small seal will stop the transmission fluid leak. easily replaced by removing the rear 13mm headed set screw in the rear tail cover. please remember that you will have to refill the transmission after removing the inner speedometer drive to replace this seal View/Change Diagram
From $1.00
Make a selection 99911329041 High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. View/Change Diagram
From $11.70
Make a selection N0122391 Known as: spring washer b 18 / spring washer View/Change Diagram
From $1.69
Make a selection
$27.45
Make a selection 90110113803 High-quality OEM (original equipment manufacturer) main bearing replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. View/Change Diagram
From $165.00
Make a selection 021109415A Discontinued by Porsche. View/Change Diagram
$10.93
Make a selection 90133231200 Known as: cup spring View/Change Diagram
From $8.21
Make a selection 90134721004 View/Change Diagram
$259.17
Make a selection 911604101AX If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle starting. Eventually you hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter be sure to check the rubber cap on the terminal for cracks which allows moisture in and it is a good idea to check your starters hardware as well. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89 914 1970-76 911 1970-73
From $399.59
Make a selection 915300911550 If you are looking for a transmission oil cooler system that is simple to install, provides lasting results and is perfect for a driver, the weekender, or for track use look no further. This kit includes a sleek high-performance oil cooler that mounts simply to the transmission cover with the included bracket and hardware. The stainless braided lines seamlessly screw into the transmission housing drain / fill plug location, no modification required. The electric, self-priming, 12 v oil pump is made with helical bronze gears, a stainless-steel shaft and a nickel plated brass body for the reliability that you expect from your Porsche. The pump includes a bracket that allows for simple installation. Simply connect...(choose a part on the right to read more)
$1,529.00
Make a selection 93010090104EQ High-quality victor reinz replacement gaskets, o-rings and washers to reseal your engine case (short block). Victor reinz has been supplying German auto manufacturers and Porsche for decades. They are a trusted name in gaskets and sealing products. This kit is complete with everything needed and we source this directly in Germany for an added level of quality. Sold individually. 1 set necessary per car. Please note: if you prefer the genuine crankshaft sealing ring, please order part # 99911342641 this also includes the intermediate shaft o-ring, part # 99970731540. Please check the model fitment tab to ensure accurate fitment.
$118.80
Make a selection 91530239906EQ Cylindrical roller bearing, located on the pinion shaft, nearest 4th gear and the tensioning plate. High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$282.70
Make a selection FVDIDA50 Complete carburetion kits ! General Fitment911 1974-77911 1978-83 911 1984-86 911 1987-89 911 1989-94 911 1994-98
$10,902.10
Make a selection SRBSK001 - allows tie rods to be adjusted downward in extra precise 1/32” (1mm) increments, taking advantage of a wider adjustment range than other kits on the market. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 914 1970-76
$301.00
Make a selection FVD721T248 This special service tool was developed for the crucial task of securing the intake and exhaust camshafts in relation to each other during base timing, etc. Trying to do this task with any other method is risking a total engine failure. Applicable: Porsche model - 996 3.4 and 986
$223.30
Make a selection 91110190100 Known as: set of crankshaft bearings comprising: / set of crankshaft bearings comprising: m >> 615 0305 / set of crankshaft bearings View/Change Diagram
$195.00
Make a selection FVD123042ATK FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)
$2,854.50
Make a selection WAP02400017 Historic distler electromatic 7500, Porsche 356 . Comes with genuine ignition key for starting the motor. Synchronized pinion gear with reverse, neutral and two forward gears. Uses two-piece steering shaft for steering and gear changes. 1:18 scale. General FitmentACCESSORY
$328.90
Make a selection RES98100000S A track favorite due to its performance gains and reliability. + 30 hp & + 25 tq gain. - catalytic bypass for track use. - weighs 59 lbs. (27,0 kg), OEM weighs 84 lbs. (38kg). - motorsport merge collector. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport muffler connections with a single gasket and flange at the header to ensure a leak free exhaust. - ecu programming (software) is necessary. The FVD Brombacherfull race exhaust system for the 981 and is one of the most technically advanced systems for Porsche to date. Our entire "brombacher" line of exhausts is manufactured to ou...(choose a part on the right to read more)
$5,710.10
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 93010501314 Genuine intermediate shaft and gear, sourced in Germany to ensure quality, reliability and precise fitment. We recommend ordering 6 qty. Oil pump lock plates part # 99903900100 for installation. Please note: please check the model fitment tab to ensure accurate fitment. Sold individually. 1 necessary per car.
From $1,661.00
Make a selection 99660610599 If you are noticing engine vibrations, misfires and even backfiring your crankshaft position sensor maybe bad. Your car's dme (ecu) uses the signal from the crankshaft position sensor to control ignition timing and fuel injection, so if your sensor is failing your engine is suffering from poor timing and is not running efficiently. This kit is complete and ready to install.
$132.75
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |